Chair Caning Instructions - Basic Chair Design

Chair Caning Instructions: Basic Chair Design.

This is project was commissioned by a grandmother who wanted her Grandmother's chairs returned to their original beauty. She had a neighbor refinish them, before bringing them to me for caning. This gave me opportunity to refresh my 7 Step Caning Instructions, while looking to see how efficient I could be. Think of this as a supplement or update to my original instructions completed about 6 years ago.

Tools.
Here are some additional tools that I have accumulated. They are all optional, as some work for me & some don't work so well for me. In order, from left to right: 1. curved spring loaded needle nose pliers - great for those hard to reach spots. 2. Pressed cane groove cleaner - haven't had the opportunity to try yet, but I know the damage I did with a regular screw driver, so hope to avoid that on the next pressed-cane project. 3. Cane Straightener - this works good to help align cane after step 4 weaving. 4. Dental Pick - with 90 degree bend. This helps to lift the cane, opening up just enough space to run a cane strand underneath. 5. Cane Needle (laying horizontal) - I find this of little help. I have tried it on step 4 weaving & am still learning to use it. However I have cut existing cane & had to replace, so use with caution.

Sizing Cane
Another new tool. This tool will help determine hole size & spacing between holes, which then tells you the size of cane to use. It will also identify the size of the cane used in an existing seat. I found that even with this tool, you have to make some choices. It seems that no chair has perfectly sized & spaced holes to match a specific cane size. You must chose which measurement most closely fits your chair hole design & which cane you think will look the best. These pictures show: measuring the hole size & distance between holes. As always, a good rule of thumb is to take a piece of cane along to match when you purchase the replacement cane.
.

Step 1. First Vertical
Start by soaking several cane in warm water for 15-20 minutes. Add a capful or two of Glycerin in the water to help the cane maintain it's flexibility & slide through tight places. The first three caning steps will go quickly & use at least 6 cane strands. It takes me about 1-1.5 hours to complete the first 3 caning steps.

Notice that the front rail has more holes than the back rail, forcing the need to use a side hole. Keep the vertical runs parallel looking. This is an indication of where a "fish-eye" will form.

Do not worry about keeping the cane tight. Leave it loose enough so that when pressed down it will reach the bottom side of the rail (about 1/2"-3/4"). The cane will naturally tighten up as the weaving steps continue. If you make the cane tight now, you will increase your difficulty of weaving later. Do not tie-off until after step 4.

Step 2. First Horizontal
Run the first horizontal on top of the Step 1 First Verticals. Efficiency tip: Because I had a long cane strand left over from step 1, I used it to start the horizontals, instead of tying off & starting a new strand.

Step 3. Second Vertical
Run the Second Vertical over the top of, & to the right of, the Step 1 first vertical. On the side rails, use the same holes as in Step 1.

Step 4. Second Horizontal. Weaving begins here.
This step takes me the longest time to complete. I probably spent 2 hours on just this step. Run the cane below Step 2 first horizontal canes. Weave the cane OVER the Step 3 vertical & UNDER the Step 1 vertical. Use extra care to keep the canes lined up vertically & horizontally. Stop after each run & re-align the cane. A caning needle may help speed up this step, however be careful in tight spaces to not cut existing canes.

After step 4 is completed, use the aligning tool to straighten each intersection of cane pairs. This is a tremendous help in preparation for the diagonal runs in Steps 5 & 6. Using two golf tees or wood pegs to line up the cane pairs works also.

Tie off the ends now beneath the seat. You may have to wet the cane ends with a damp cloth, to regain flexibility. Loop the cane end twice under the cane & cut the end leaving about 1/4".

If you stop between steps, lay a warm damp cloth or paper towel on the caned seat while you soak your next cane strands. This helps to regain flexibility in the seat cane & makes it easier to work.

Step 5. First Diagonal
The canes are now run diagonally from front to back. You can start from either corner actually, though some professionals preferred one way or the other (Left Back towards Right Front VS Right Back towards Left Front). Because I had left over cane ends at the back right corner, I started there. If unsure how to start, take a small length of cane & run a practice cane from back towards front. This will help to visualize how the cane should run. If you have difficulty pulling the cane through, STOP & check to make sure your running it correctly. If the cane is cutting or splitting, you may be running it incorrectly.

Weave OVER the Vertical pairs & UNDER the Horizontal pairs. Notice that the cane fits snuggly into a natural slot created from the intersection of the Vertical & Horizontal canes. If the cane is not fitting into this slot, it may cut the cane. Pull the cane tight as you weave now. This will tighten up all of the seat.

Forming the "X" takes place on the diagonals. Take extra care to run the cane to that furthest hole on the rail, pulling the vertical or horizontal pairs tighter together. The "X" is formed on the rail when the cane is run to cover the verticals or horizontals on the rails. The "X" makes the caned seat somewhat stronger & more attractive. The first leg of the "X" is created in step 5 & the second leg comes from step 6.

Step 6. Second Diagonal
Weave UNDER the Vertical pairs & OVER the Horizontal pairs. Again, notice that the cane fits snuggly into a natural slot created from the intersection of the Vertical & Horizontal canes. If the cane is not fitting into this slot, it may cut the cane. The second leg of the "X" is formed here. Take the extra effort to look for it & complete it, even if you have to stretch to the next hole or weave under some tight intersections.

Step 7. Border
The border finished the seat. Use a wide border cane to lay flat on the seat covering the holes. Use same sized cane as used in the seat to loop over the border to hold in place. The ends of the border cane can be run in one corner hole to the next corner hole. On square seats the border cane ends can be simply "pegged" or "couched" to secure them.

To Peg the border ends, simply form to fit, a small dowel point & force it into position.

The picture below shows the "couching" corners. This is where one border cane end is run down the corner hole. The second border cane is placed in the hole. a small dowel point is forced down the hole to hole the ends. Then the second border cane is neatly folded over the dowel forming a 90 corner. Couching the corners is now my preferred technique, as I think it looks more professional.

Here is the finished seat. Notice the "X" formed on each rail. Celebrate the successful completion of another beautiful caning project. These are now an heirloom that will be passed down, Grandma's chairs going to Great-Granddaughter, who may be able to pass on to her child.

In addendum: One of the two chairs in this project had 60 holes, the other had 72. The smaller chair took me about 5 hours to complete. I was trying to see how fast I could complete this basic chair. The larger took a little over 6 hours.